Thinktool PAD 8 is a high-end product of the thinkcar brand. It is not only a simple full-system diagnostic device, but also includes 34 maintenance functions.
The most important thing is to support tire pressure programming, ECU Coding and motion testing. THINKTOOL PAD 8 is a professional all system diagnostic scanning tool. THINKTOOL PAD 8 is a professional system-wide diagnostic scanning tool.
It can scan the available modules of the vehicle including PCM, ECM, EPS, PDM, TPM, BCM, ABS and SCCM, etc. And has the Complete code, real-time data, active testing, ECU information, adaptation, matching, ECU coding and other functions. THINKCAR THINKTOOL PAD 8 Support 34+ Special Functions. The lightening of the car maintenance light indicates that the vehicle needs maintenance.
Reset the cluster or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle. DPF regeneration may be performed in the following cases.AThe exhaust back pressure sensor is replaced. CThe fuel additive nozzle is removed or replaced. DThe cataytic oxidizer is removed or replaced. EThe DPF regeneration MIL is on and maintenance is performed. FThe DPF regeneration control module is replaced. The feature is used to initialize the adaptive headlamp system.
According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture. This function is used to learn the EGR(Exhaust Gas Recirculation)valve after it is cleaned or replaced. If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad.
Reset must be performed in the following cases. AThe brake pad and brake pad wear sensor are replaced. BThe brake pad indicator lamp is on. CThe brake pad sensor circuit is short, which is recovered.DThe servo motor is replaced. To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immoblizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ingnition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed. This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. Use this function to activate the electronic water pump before venting the cooling system. To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.
After replacing the steering angle position sensor, replacing steering mechanical parts(such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle. Writing injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that cylinder can better indentify injectors to accurately control fuel injection. This function is applied to match the seats with memory function that are replaced and repaired. This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.Battery matching must be performed in the following cases. Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information. If the related control module detects false information, it will invalidate some electric auxiliary functios, such as automatic start&stop function, sunroof without one-key trigger function, power window without automatic function. Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more accurately, which can avoid an error message displaying on the instrument panel.
This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collides and the airbag deploys, the corresponding fault code of the colision data appears, the airbag indicator lights up, and the fault code can't be cleared. Since the data inside the airbag computor is disposable, it is required that all new accessories must be ewplaced, but after performing this function, the data of the airbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and the airbag computer can continue to use.This function is used to set the size parameters of the modified or replaced tire. Acluster reset is to coopy, write, or rewrite the value of kilometers in the chip of cluster by using a car diagnostic computer and data cable, so that the cluster shows the actual cluster. BUsually when the cluster is not correct due to the damaged vehicle speed sensor or cluster failure, it is necessary to do cluster reset after maintenance. When the ABS contain air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced, the ABS bleeding function must be performed.
The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. Lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started. The diagnostic device detects the DTC P1336'gear not learned'. In this case, you must use the diagnostic device to perform gear learning for the car. After gear learning is successful, the MIL turns off.After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC'gear not learned is present, gear learning must be performed. This function is used to change the system language of the vehicle central control panel.
After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or coontrol module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration. This function is applied to set or learn Air/Fuel ratio parameters.
Nox sensor is a sensor used to detect the content of nitrogen oxides (NOx)in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU. After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting functionmust be performed to reset tire pressure and turn off the tire pressure MIL.
Tire pressure resetting mustbe performed after maintenance is performed in the following cases: tire pressure is too low, tire leaks, tirepressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, andtire is replaced for the car with tire pressure monitoring function. This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox isdisassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impactproblem. In this case, this function needs to be done so that the gearbox can automatically compensateaccording to the driving conditions so as to achieve more comfortable and better shift quality.This function can set the sunroof lock off, closed when it rains, sliding/tilting sunroof memory function, temperature threshold outside the car etc. This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware). ECU Coding and Bi-directional Control. THINKCAR Thinktool Mini supports ECU coding function on a large amount of makes, including for Benz, for Ford and more.
Active test is to test output elements. You can figure out whether a specific subsystem or component in your car functions well or not by using this tool to make the tester outputs function instead of checking in ignition status. There is no complicated operation, and there will be a full operation prompt when starting up.
Search VIN Reading and Quick Diagnostic report printing. THINKTOOL PAD8 provides multiple methods of VIN identification without navigating through the complex car identification process, saving you time and increasing your productivity. As well as providing a diagnostic report, it is convenient for you to compare the condition of the car at different times. THINKCAR THINKKTOOL PAD 8 Support remote diagnosis and feedback.If you enter an unsolved problem during use, our engneer will operate it for you remotely. You can also give us feeback about your suggestion or needs, we will keep improve our best. English, German, Italian, Japanese, Russian, French, Spanish, Portuguese, Polish, Turkish, Dutch, Hungarian, Chinese(traditional). THINKCAR THINKTOOL PAD 8 Support 10000+ models.
CONNECT BY BLUETOOTH, UP TO 10M. PRODUCT PARAMETER AND PRODUCT DETAILS. Charging Cable(Micro USB)1. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Exterior Parts & Accessories\Body Moldings & Trims". The seller is "dukenukemmaxxx" and is located in this country: US.This item can be shipped worldwide.