Brake System :if you feel the brake pedal is mushy and notice unusual odor or noise, etc. A properly operating brake system is critical to ensure safe vehicle control and operation; Emission System :if the system is affected by vehicle age or poor quality fuel. A good emission system reduces harmful gases to a large degree and protects you from being fined; Fuel system :if vehicle won't start or "Check Engine" light is illuminated. Check car's fuel system regularly ensures the best performance of your car with the lowest emissions; Transmission System :if your car is slipping or difficult to shift. The system plays an important part in the overall performance of your car; Wiper System :if you observe chattering or streaking wiper.
If the car is not regularly checked, the accident might happen because you can't see clearly; Light System :if you see rapid signal blinking or dimming lights. Support ECU Coding and Active Test(Bi-directional). The ECU Coding of this diagnostic tool can work on most vehicle makes.
It is used to reprogram adaptive data for vehicle control modules after repairs or replacements of vehicle parts. The Active Test function is used to access vehicle-specific subsystem and component tests. DS600 Support 28+ Special Reset Function. Oil Reset The lightening of the car maintenance light indicates that the vehicle needs maintenance. Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.
DPF regeneration may be performed in the following cases: aThe exhaust back pressure sensor is replaced. EThe DPF regeneration MIL is on and maintenance is performed. FThe DPF regeneration control module is replaced.
AFS(headlamp) Reset The feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture. EGR Adaption This function is used to learn the EGR(Exhaust Gas Recirculation)valve after it is cleaned or replaced.
Brake-pad Reset If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad.Reset must be performed in the following cases: aThe brake pad and brake pad wear sensor are replaced. BThe brake pad indicator lamp is on. CThe brake pad sensor circuit is short, which is recovered. DThe servo motor is replaced.
IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immoblizer control system on the car identifies and authorizes remote control keys to normally use the car. When the ingnition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed.Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. Steering Angle Reset To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts(such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle.
Injector Coding Writing injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that cylinder can better indentify injectors to accurately control fuel injection. Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. Battery Matching This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done. Battery matching must be performed in the following cases: aMain battery is replaced.
Battery matching must be performed to clear original low battery information and prevent the related control module from detecting false information. If the related control module detects false information, it will invalidate some electric auxiliary functios, such as automatic start&stop function, sunroof without one-key trigger function, power window without automatic function. Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more accurately, which can avoid an error message displaying on the instrument panel. Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collides and the airbag deploys, the corresponding fault code of the colision data appears, the airbag indicator lights up, and the fault code can't be cleared.
Since the data inside the airbag computor is disposable, it is required that all new accessories must be ewplaced, but after performing this function, the data of the airbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and the airbag computer can continue to use. Tyre Reset This function is used to set the size parameters of the modified or replaced tire.
ODO Reset aODO reset is to coopy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. BUsually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODO reset after maintenance. ABS Bleeding When the ABS contain air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity. If the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced, the ABS bleeding function must be performed. Language Change This function is used to change the system language of the vehicle central control panel.
Adblue Reset After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or coontrol module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration. A/F Reset This function is applied to set or learn Air/Fuel ratio parameters.
Nox Sensor Reset Nox sensor is a sensor used to detect the content of nitrogen oxides (NOx)in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU. Sunroof Initialization This function can set the sunroof lock off, closed when it rains, sliding/tilting sunroof memory function, temperature threshold outside the car etc. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware) And many more..... Italian, English, German, Japanese, Russian, French, Spanish, Portuguese, polish, Turkish, Dutch, Greek, Hungarian, Arabic, Danish, Korean, Persian, Romania, Serbia, Finnish, Swedish, Czech, Chinese(traditional).For BUICK, For CADILLAC, For CHEVROLET, For CGRYSLER, For DODGE, For FIAT(BRAZIL), For FORD, For FORD(AUSTRALIA), For GM, For GM(BRAZIL), For JEEP, For LINCOLN. For ABARTH, For ALFA ROMEO, For ASTON MARTIN, For AUDI, For BENTLEY, For BMW, For BUGATTI, For CITROEN, For DACIA, For DR, For FORD(EUROPE), For FERRARI, For FIAT, For GAZ, For OPEL(SOUTH AFRICA), For IVECO, For IZH, For JAGUAR, For LAMBORGHINI, For LANCIA, For LAND ROVER, For MASERATI, For MAYBACH, For MERCEDES-BENZ, For MINI, For OPEL, For PAZ, For PEUGEOT, For PORSCHE, For RENAULT, For ROLLS ROYCE, For ROVER, For SAAB, For SEAT, For SEAZ, For SKODA, For SMART, For SPRINTER, For UAZ, For VAUXHALL, For VAZ, For VOLVO, For VW, For ZAZ. For ACURA, For DAEWOO, For DAIHATSU, For HOLDEN(AUSTRILIA), For HONDA, For HYUNDAI, For IKCO, For INFINITI, For ISUZU, For KIA, For LEXUS, For LUXGEN, For MAHINDRA, For MAHINDRA(INDIA), For MARUTI, For MARUTI(INDIA), For MAZDA, For MITSUBISHI, For MVM, For NISSAN, For GTR(NISSAN), For PERODUA, For PERODUA(MALAYSIA), For PROTON, For PROTON(MALAYSIA), For SAMSUNG, For RENAULT SAMSUNG, For SAIPA, For SSANGYONG, For SUBARU, For SUZUKI, For TATA, For TATA(INDIA), For ISUZU(THAILAND), For TOYOTA, For UNITED PAKISTAN. For SENOUA(BAIC), For WEIWANG(BAIC), For BJEV, For BAIC, For BRILLIANCE, For BYD, For CHANGAN, For CHANGHE, For BUICK(CHINA), For CHERY, For CHANCHE SUZUKI, For DFCITROEN, For ECUAID, For FAW(TIANJIN), For FOTON, For GEELY, For JINLONG, For GONOW, For GWM, For HAFEI, For HAIMA, For JAC, For JAC REFINE, For SHIERAY, For JMC, For JOYLONG, For LIFAN, For MG(SAIC), For QOROS, For MAXUS, For SGM, For SOUEAST, For SPARK, For SGMW, For DFSK, For XINKAI, For POLARSUN, For ZX AUTO, For ZOTYE. Power Key Press and hold it for 3 seconds to turn it off Press and hold it for 8 seconds to perform forced shutdown Press it once to activate or turn off the device 3. Type C Charging Slot:connect the suppiled charger for charging 4. USB Port:Reserved for add-on modules and other device with similar port 5. Backplane:remove the backplane of the tablet, and install function modules on the backend 8. PIN:Used for communication between the function expansion module and the host 9.
Adjustable Kickstand:Flip out it to 180-degree angle and work comfortable at your desk, or hang it on automotive part 10. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Exterior Parts & Accessories\Body Moldings & Trims".
The seller is "dukenukemmaxxx" and is located in this country: US. This item can be shipped worldwide.